3.Guide: widely used in living room, bathroom, kitchen wall floor,
such as indoor space shop pastes, products with a long time color
retention, hard and durable, and other characteristics, indoor use
can be durable and new. Product features can also be used for
outdoor use, if need to lay outside, depending on the user's
requirements for non-slip.
Glaze: Concave-convex grinding face plus flash glaze, non-slip,
easy to clean.
Design pattern: Multiple patterns combination, can be mixed with
multiple colors.
4. Raw material and advantages:
CHORA porcelain tile, green building material
CHORA porcelain tile is hard and condense, superficial hardness is
very high (hardness 4-5), is scratch-resistant, wear, shock,
rupture and compression and have excellent heat-, corrosion- and
stain-resistance, not being distorted, split and being-resistant to
discoloration, fading, durable and maintenance-free, furthermore,
it does not contain any pollution and radiation, thus is an
environment-friendly building material, porcelain tile is bright
with accurate color dimensions, high-quality finish, fine
durability and compression-resistance fine air permeability
renewable, environment-friendly
3-test report and certification: Foshan Boli Ceramics Company
Limited is one of the largest building material enterprises in
South China, we mainly produce porcelain tile, cement tile,
polished tile
Our products sell well in domestic market and abroad such as
Europe, Middle East, Egypt, South Africa, Middle Africa, Italy,
South and East Asia, we have a team of hardworking and innovating
technical working staff, we have more than 10-professional
production lines and first-class equipment to satisfy the
professional technology requirements
5.About laying and pasting construction:
1, when opening the box, should recognize the product
specifications, dimensions, color number, etc., the same color
number of the product affixed to the same position, do not mix the
products of different color numbers together pasted(unless
consciously required to obtain Special decorative effects in the
figure)
2, before pasting first on the ground test, after using the same
color number and size, you can use the adjacent color number and
size, and different color number, size tile classification, and
then in the bottom of the brick for use Number to indicate. If the
brick surface has a pattern or directional pattern, the product
should be unified according to the direction of the pattern, in
order to best decorative effects.
3, at present, the tile pasting mostly uses wet pasting and dry
pasting two methods.
4, when paving the floor brick, it is recommended that the surface
area of cement mortar paving should not be too large, so as not to
find the surface cement mortar more than the initial coagulation
time(about 45 minutes), resulting in the tile and adhesive layer
adhesion is not dense Real, causing quality problems such as air
drums.
5, when leaving seam pasting, polished brick spacing 2mm-5mm is
appropriate. The polished brick and the wall junction leave a seam
of 3mm-5mm.
6, pasting should be carried out after the base is compacted. When
tiling tiles, the tiles and the pasting surface are first presented
at a certain angle(about 15 degrees), and then pushed gently to the
horizontal direction by hand to balance the bottom of the brick and
the pasting surface.This facilitates the elimination of bubbles;
Then tap the brick surface with a hammer handle, so that the bottom
of the brick can eat pulp, so as not to produce an empty drum
phenomenon; Then knock the brick surface to level with a wooden
hammer and measure it with a horizontal ruler to ensure The tile
pasting level.
7, the product pasted for about 1 hour(depending on the climate and
the degree of cement condensation), we must use the wood bran or
sponge to clean the cement mud in time, to avoid the surface
contamination time is too long, it is difficult to clean up.
8, about 12 hours after the product is pasted, hit the ground with
a wooden hammer in time to check whether there is an empty drum
phenomenon. All brickwork should be done in time to remove the
surface dirt, 24 hours before walking.
9, pasted tiles within 48 hours, it is best not to use large-scale
waxing and other electric equipment, so as not to tile and adhesive
layer later shock and lead to unnecessary empty drum phenomenon.
